ANKER Y1010 Charging Dock for Oculus Quest 2 User Manual - Manuals+ (2023)

ANKER Y1010 Charging Dock for Oculus Quest 2

Safety Instructions

Read all the instructions before using the product, refer to the information on the exterior bottom enclosure for electrical and safety information before installing or operating the product.

• Store the product in a cool and dry place.
• Do not store the product in a hot or humid environment.
• Use of a power supply or charger not recommended or sold by the product manufacturer may result in a risk of fire or injury to persons.
• Operating temperature should be between 0°C to 35°C.
• Do not disassemble the product.
• Do not leave or dispose of the product in both extremely low air pressure and extreme heat such as sunshine, fire, or the like.
• Do not clean the product with harmful chemicals or detergents.
• Misuse, dropping or excessive force may cause product damage.
• When disposing of secondary cells or batteries, keep cells or batteries of different electrochemical systems separate from each other.
• Be aware the discharged battery may cause fire or smoke, tape the terminals to insulate them.
• Do not subject the product to mechanical shock, crushing, or cutting.
• Do not short-circuit the product or be short-circuited by other metal objects.
• Do not use any cell or battery which is not designed for use with the equipment.
• To reduce the risk of injury, close supervision is necessary when this product is used near children or keep the product out of the reach of children.
• Do not put fingers or hands into the product.
• Do not use the product in excess of its output rating. Overload outputs above rating may result in a risk of fire or injury to persons.
• Do not use the product that is damaged or modified. It may exhibit unpredictable behavior resulting in fire, explosion, or risk of injury
• Have servicing performed by a qualified repair person using only identical replacement parts. This will ensure that the safety of the product is maintained.
• Switch off the device when not in use.
• Do not install this equipment in a confined or building-in space such as a bookcase or similar unit, and remain in good ventilation conditions at an open site.
• The batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire, or the like.
• Attention should be drawn to the environmental aspects of battery disposal. Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
• Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.
• A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

CAUTION: Risk of fire or explosion if the battery is replaced by an incorrect type. Replace only with the same or equivalent type. Rechargeable Ni-MH battery mode: Ni-MH AA 1800mAh 1.2V, Made By: Yiyang Corun Battery Co., Ltd.
WARNING: Use only power supplies listed in the user instructions. Adapter Model(s): ASUC49w-P27W12, Made By: Shenzhen Aquilstar Technology Co., Ltd.

At a Glance

1. Charging dock for headset
2. USB-C input port
3. Magnetic output connector
4. Charging dock for controllers
5. Power LED indicators (Left/Right: controllers; Middle: headset)
6. Charging pin
7. Magnetic USB-C plug
8. Replacement battery door
9. Rechargeable batteries

Using your Charging Dock

1. Insert the magnetic USB-C plug into the USB-C charging port of your headset.
   
2. Place your headset into the charging dock and make sure that the magnetic USB-C plug adheres to the magnetic output connector.
   
3. Remove the original battery door and alkaline battery from controllers.
   
4. Install the rechargeable battery with correct polarity, make sure that the 2 bare metal sheets align with the outer frame of the battery compartment. Close the battery door and place the controllers into the charging dock.
   
5. Connect the charging dock to the power supply by using the provided USB-C charging cable and charger.
   >>> The power LED indicators will turn on.
   

• If you use a charger with an output of 5~15W, the charging dock will give priority to charge the headset. If the output of the charger is less than 5W, the charging dock won’t work.
• Normally, the voltage of Ni-MH batteries will drop after being fully charged. After the controllers are fully charged and left on the charging dock for more than 6 hours, the battery level displayed on your Quest 2 or in the App will be less than 100%, but will still have enough power to last for more than 10 hours.

LED Light Guide

	Solid amber for 5 seconds	Connected to power
	Solid amber	Being charged
	Solid green	Fully charged
	Flashing amber	Working improperly

Specifications

FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

(1) Reorient or relocate the receiving antenna.
(2) Increase the separation between the equipment and receiver.
(3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
(4) Consult the dealer or an experienced radio / TV technician for help.
The following importer is the responsible party (for FCC matters only).
Company Name: Fantasia Trading LLC
Address: 5350 Ontario Mills Pkwy, Suite 100, Ontario, CA 91764
Telephone: +1-800-988-7973
Notice to Canadian users
This device complies with Industry Canada license-ICES-003. Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device.
CAN ICES-3（B）/ NMB-3（B）

Declaration of Conformity
Hereby, Anker Innovations Limited declares that the product type Y1010 is in compliance with Directives 2014/35/EU & 2014/30 /EU & 2011/65/ EU & 2009/125/EC.

The full text of the EU declaration of conformity is available at the following internet address: https://www.anker.com
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong

ANKER TECHNOLOGY (UK) LTD
Suite B, Fairgate House, 205 Kings Road, Tyseley, Birmingham, B11 2AA, United Kingdom
Anker Innovations Deutschland GmbH Georg-Muche-Strasse 3, 80807 Munich, Germany

	Indoor use only.
	This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Follow local rules and never dispose of the product and rechargeable batteries with normal household waste. Correct disposal of old products and rechargeable batteries helps prevent negative consequences for the environment and human health.

[emailprotected]
[emailprotected]
(For Middle East and Africa Only)
(US) +1 (800) 988 7973 Mon-Fri 9:00am – 5:00pm (PT)
(UK) +44 (0) 1604 936200 Mon-Fri 6:00 – 11:00 (GMT)
(DE) +49 (0) 69 9579 7960 Mo-Fr 6:00 – 11:00

Documents / Resources

References

• Anker | Charge Fast, Live More
• download
• download
• Anker | Charge Fast, Live More
• download